Climate Control Diagnostic Tables

CHANNEL 01

ERROR CODE ERROR CORRECTION OF ERROR

00
No error recognized
--

01
Inside temp sensor G56 (instrument channel), open circuit

Check affected component and related wiring according to wiring diagram.

02
Inside temp sensor G56 (inst panel), short circuit.

Check affected component and related wiring according to wiring diagram.

03
Outside temp sensor G57 (plenum) open circuit

Check affected component and related wiring according to wiring diagram.

04
Outside temp sensor G57 (plenum) short circuit

Check affected component and related wiring according to wiring diagram.

05
Outside temp sensor G57 (cowl) open circuit

Check affected component and related wiring according to wiring diagram.

06
Outside temp sensor G57 (cowl) short circuit
Check affected component and related wiring according to wiring diagram.

07 Feedback potentiometer on adj motor for temp reg flap, V68 (interruption / open) Check temp regulating flap servo motor V68 (w/ feedback potentiometer) SEC D8-190

08 Feedback potentiometer on adj motor for temp reg flap, V68 (short circuit) Check temp regulating flap servo motor V68 (w/ feedback potentiometer) SEC D8-190

09 Coolant temp sensor G62, open circuit Check coolant temp sensor G62 and its wiring according to diagram.

10 Coolant temp sensor G62, short circuit Check coolant temp sensor G62 and its wiring according to diagram.

11 Inside temp sensor G68 (roof), open circuit Check inside temp sensor (roof) and wiring...

12 Inside temp sensor G68 (roof), short circuit Check inside temp sensor (roof) and wiring...

13 Electrical system voltage is or was once less than 9.5V but greater than 5V during the current driving period. Note: Values less than 5V are recognized as open low pressure switch. Check electrical system voltage display. Section D8-260

14 Compressor off; high pressure switch F118 (red housing) cycled 8 times. Check high pressure switch F118 (sec D8-230)

15 Adjustment motor for temp reg flap V68 (with feedback potentiometer) is set improperly. Check temp regulating flap servo motor V68 (w/ feedback potentiometer) Sec D8-190

16 High pressure switch F118 has open circuit or cycled at least one time during current driving period. Check high pressure switch F118 (red housing) and it's wiring according to wiring diagram.

ERROR CODE	ERROR	CORRECTION OF ERROR
00	No error recognized	--
01	Inside temp sensor G56 (instrument channel), open circuit	Check affected component and related wiring according to wiring diagram.
02	Inside temp sensor G56 (inst panel), short circuit.	Check affected component and related wiring according to wiring diagram.
03	Outside temp sensor G57 (plenum) open circuit	Check affected component and related wiring according to wiring diagram.
04	Outside temp sensor G57 (plenum) short circuit	Check affected component and related wiring according to wiring diagram.
05	Outside temp sensor G57 (cowl) open circuit	Check affected component and related wiring according to wiring diagram.
06	Outside temp sensor G57 (cowl) short circuit	Check affected component and related wiring according to wiring diagram.
07	Feedback potentiometer on adj motor for temp reg flap, V68 (interruption / open)	Check temp regulating flap servo motor V68 (w/ feedback potentiometer) SEC D8-190
08	Feedback potentiometer on adj motor for temp reg flap, V68 (short circuit)	Check temp regulating flap servo motor V68 (w/ feedback potentiometer) SEC D8-190
09	Coolant temp sensor G62, open circuit	Check coolant temp sensor G62 and its wiring according to diagram.
10	Coolant temp sensor G62, short circuit	Check coolant temp sensor G62 and its wiring according to diagram.
11	Inside temp sensor G68 (roof), open circuit	Check inside temp sensor (roof) and wiring...
12	Inside temp sensor G68 (roof), short circuit	Check inside temp sensor (roof) and wiring...
13	Electrical system voltage is or was once less than 9.5V but greater than 5V during the current driving period. Note: Values less than 5V are recognized as open low pressure switch.	Check electrical system voltage display. Section D8-260
14	Compressor off; high pressure switch F118 (red housing) cycled 8 times.	Check high pressure switch F118 (sec D8-230)
15	Adjustment motor for temp reg flap V68 (with feedback potentiometer) is set improperly.	Check temp regulating flap servo motor V68 (w/ feedback potentiometer) Sec D8-190
16	High pressure switch F118 has open circuit or cycled at least one time during current driving period.	Check high pressure switch F118 (red housing) and it's wiring according to wiring diagram.